收藏本站
Chapter 6: Board Test System
6–3
Preparing the Board
Preparing the Board
With the power to the board off, perform the following steps:
1. Connect the USB cable to the board.
2. Verify the settings for the board settings DIP switch bank (SW4) match Table 4–2
on page 4–3 .
3. Set the rotary switch (SW2) to the 1 position.
4. Verify the settings for the JTAG DIP switch bank (SW6), located on the back of the
board, match Table 4–4 on page 4–4 . These settings determine the devices to
include in the JTAG chain.
f
For more information about the board’s DIP switch and jumper settings,
refer to the Stratix IV GX FPGA Development Board Reference Manual .
5. Turn the power to the board on. The board loads the design stored in the user
portion of flash memory into the FPGA. If your board is still in the factory
configuration or if you have downloaded a newer version of the Board Test
System to flash memory through the Board Update Portal, the design that tests the
GPIO, SRAM, and flash memory loads.
c
To ensure operating stability, keep the USB cable connected and the board
powered on when running the demonstration application. The application
cannot run correctly unless the USB cable is attached and the board is on.
Running the Board Test System
To run the application, navigate to the <install
dir> \kits\stratixIVGX_4sgx230_av\examples\board_test_system directory and run
the BoardTestSystem.exe application.
1
1
On Windows, click Start > All Programs > Altera > Audio Video Development Kit,
Stratix IV GX Edition < version > > Board Test System to run the application.
A GUI appears, displaying the application tab that corresponds to the design running
in the FPGA. The Stratix IV GX FPGA development board’s flash memory ships
preconfigured with the design that corresponds to the Config , GPIO , and
SRAM&Flash tabs.
If you power up your board with the rotary switch (SW2) in a position other than the
1 position, or if you load your own design into the FPGA with the Quartus II
Programmer, you receive a message prompting you to configure your board with a
valid Board Test System design. Refer to “The Configure Menu” for information about
configuring your board.
Using the Board Test System
This section describes each control in the Board Test System application.
? November 2009
Altera Corporation
Audio Video Development Kit, Stratix IV GX Edition User Guide
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
DKUSB-1 KIT DEV FOR MB86065
DLD101-7 IC LED DRIVER HP CONST CURR 8DFN
DLP-2232H-PSOC5 MODULE PSOC5 USB ADAPTER FT2232H
DM163014 BOARD DEMO PICDEM4 12F629,16F630
DM163022-1 BOARD DEMO PIC16F87X PIC18FXX2
DM163030 KIT DEV PICDEM LCD2
DM163035 KIT DEVELOPMENT PICDEM LAB
DM164120-1 BOARD DEMO PICKIT 2 LP COUNT
相关代理商/技术参数
DKWF111 功能描述:WiFi/802.11开发工具 WF111 SDIO Eval kit RoHS:否 制造商:Roving Networks 产品:Evaluation Boards 工具用于评估:RN-171 支持协议:802.11 b/g 频率:2.4 GHz 接口类型:UART 工作电源电压:2 V to 16 V
DKWF121 功能描述:WiFi/802.11开发工具 WF121 Dev Kit RoHS:否 制造商:Roving Networks 产品:Evaluation Boards 工具用于评估:RN-171 支持协议:802.11 b/g 频率:2.4 GHz 接口类型:UART 工作电源电压:2 V to 16 V
DKWT32I 功能描述:BLUETOOTH DEVELOPMENT KIT 制造商:silicon labs 系列:- 零件状态:有效 类型:收发器; 传统蓝牙? 频率:2.4GHz 配套使用产品/相关产品:WT32i 所含物品:板 标准包装:1
DKXC5VADAPT-1 功能描述:DAC DK FPGA ADAPTER BOARD RoHS:是 类别:编程器，开发系统 >> 配件 系列:- 标准包装:1 系列:- 附件类型:适配器板 适用于相关产品:RCB230，RCB231，RCB212 配用:26790D-ND - RCB BREAKOUT BOARD RS232 CABLE
DKYRITRPDR2B30 制造商:OMRON AUTOMATION AND SAFETY 功能描述:TEXAS INSTRUMENTS V640RFID TAG
DKY-RI-TRP-DR2B-30 制造商:OMRON AUTOMATION AND SAFETY 功能描述:TEXAS INSTRUMENTS V640RFID TAG 制造商:Omron Electronic Components LLC 功能描述:TI V640RFID tag 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:Texas Instruments V640RFID tag
DK-Z7-VIDEO-CES-G 制造商:Xilinx 功能描述: 制造商:Xilinx 功能描述:ZYNQ-7000 VIDEO AND IMAGING KIT 制造商:Xilinx 功能描述:IMAGING / VIDEO KIT ZYNQ-7000 制造商:Xilinx 功能描述:IMAGING / VIDEO KIT, ZYNQ-7000
DK-Z7-VIDEO-CES-G-J 制造商:Xilinx 功能描述:ZYNQ-7000 VIDEO/IMAGE KIT JAPAN